Knowledge Center

Technical Resource Hub

Practical guidance from medMETRIC's engineering team — helping biomedical technicians, hospital procurement officers, and clinical staff maintain the highest standards of equipment safety and performance.

WATER TREATMENT HEMODIALYSIS

Understanding Hemodialysis Water Quality Standards

Water quality is the most critical and most frequently overlooked factor in dialysis safety. Each patient session exposes them to 120–150 litres of dialysate that must meet strict microbiological and chemical purity standards.

Key parameters to monitor in your RO system

CONDUCTIVITY

Below 10 µS/cm

Readings above this at point of use indicate membrane degradation or bypass contamination.

BACTERIAL COUNT

Below 100 CFU/mL

AAMI standard. EUDRACT stricter guideline requires below 50 CFU/mL for dialysis water.

ENDOTOXINS

Below 0.25 EU/mL

Standard dialysis limit. Online HDF requires below 0.03 EU/mL — ultrapure grade.

pH RANGE

5.0 – 7.0

Required pH range for RO permeate in dialysis applications. Outside this range accelerates membrane wear.

Common causes of RO membrane fouling

  1. Inadequate pre-treatment — hardness, chlorine, or iron in feed water
  2. Insufficient disinfection frequency
  3. Delayed membrane replacement beyond rated lifespan
  4. Bypassed or non-functional UV lamp

medMETRIC supplies FilmTec BW-8040 membranes and TUV TL 6W G5 UV lamps. Contact us for supply and installation →


HEMODIALYSIS CHECKLIST

Preventive Maintenance Checklist: B.Braun Dialog+

A structured PM schedule dramatically reduces the risk of mid-session machine failure. Use this as a basis for your biomedical department's quarterly maintenance visits.

D

Daily — Operator Level

  • Self-test completion — all parameters green
  • Conductivity reading within normal range
  • Temperature alarm test
  • Blood pump speed accuracy check
  • Alarm audio/visual test
Q

Quarterly — Biomedical Engineer

  • Full calibration of conductivity cells
  • Pressure transducer calibration
  • Blood leak detector functional test
  • Air bubble detector test
  • Hydraulic pathway inspection
  • Error log review & documentation
A

Annual — Qualified Engineer

  • Full hydraulic pathway replacement
  • Pump head replacement
  • Full electrical safety test (IEC 62353)
  • Calibration certificate issue

medMETRIC engineers are qualified to perform quarterly and annual PM on B.Braun Dialog+ systems under service contract. Request a PM visit →


PROCUREMENT WATER TREATMENT

What to Look for When Procuring an RO Water Treatment System

Procuring the wrong RO system — or the right system without local support — is one of the most expensive mistakes a dialysis facility can make.

MEMBRANE TYPE

TFC — Thin Film Composite

The clinical standard. Avoid older CA (Cellulose Acetate) membranes in dialysis applications.

CHASSIS MATERIAL

ASTM 316L Stainless Steel

Required for dialysis-grade systems (as in Rivamed RM-3000). Avoid painted steel or aluminium in water contact pathways.

DISINFECTION

Integrated Disinfection Mode

System must have a built-in thermal or chemical disinfection cycle. Non-negotiable for clinical use.

CERTIFICATION

CE + ISO 13485

Request both CE marking and ISO 13485 compliance documentation from any supplier before signing a purchase order.

medMETRIC is the local technical support partner for Rivamed water treatment systems in Ethiopia. We maintain local spare parts inventory including membranes and UV lamps. Request a consultation →


CSSD COMPLIANCE

CSSD Compliance: Key Standards Every Biomedical Engineer Should Know

Central Sterile Supply Departments are subject to a layered set of national and international standards. Non-compliance risks patient safety and exposes facilities to regulatory action.

ISO

ISO 17665

Sterilization of health care products via moist heat. The primary standard for autoclave validation.

EN

EN 285

Large steam sterilizers specification — governs design, performance, and testing requirements.

WHO

WHO Decontamination Guidelines

Decontamination and reprocessing of medical devices for health-care facilities — essential for procurement and commissioning decisions.

medMETRIC provides compliance documentation support and cycle validation services for Rivamed CSSD systems. Request validation support →

Have a technical question not covered here?

Submit it via our service request form and our engineering team will respond directly.

Ask Our Engineers